overload, crane overload, overload detection

Technical specifications, drawing and dimensions table (scroll further down)

RON 1000 is a low headroom, electromechanical Overload Detector. It may be configured to trigger any desired electrical alarm supplied by the customer including stopping the lift, for overload detection and prevention when an unsafe overload condition occurs.

Overload during lifting: hoist or crane overload is dangerous and might result in an accident. Overload detection is important for prevention of crane overload.

The low headroom RON 1000 Overload Detector is designed to be installed on the dead end of a chain or wire rope or can be used directly between the hoist and its trolley.

The devices are supplied factory calibrated and ready for installation. Available in a wide variety of capacities, the RON 1000 can be supplied in capacities ranging from 250 kgs (500 lbs) to 10,000 kgs (20,000 lbs). Each unit is initially adjusted to give the user an overload indication at 105% of rated capacity.

RON 1000 - Standard Type

View product brochure and technical specifications (PDF)

RON 1000 - Chain Type

View product brochure and technical specifications (PDF)

RON 1000 - Hook Type

View product brochure and technical specifications (PDF)

Specifications

Options

Safety Factor: 5:1. Each system proof-loaded to 200% of capacity (certified).

Switching Nature: Normally open and/or normally closed.

Rating: 0.5A @ 50 VDC, 0.5A @ 125 VAC.

Life Expectancy: Electrical: over 1 million operations. Mechanical: over 5 million operations.

Approved by: UL, CSA, Semko VDE.

Environment: Weatherproof, NEMA 4, IP 65.

Temperature Range: -4°F to +175°F (-20°C to + 80°C).

Cable Length: 9.5' (3m).

Material: High strength, low alloy steel

Wiring

Options:

Additional detection point

Fatigue rated structure

RON 1000 - S

15.08.07

Cat no.	Cap.	D Min.		A		E Max.		F Max.		C Max.		B Max.
Cat no.	tons	mm	inch	mm	inch	mm	inch	mm	inch	mm	inch	mm	inch
S-002	0.25	25	1	60	2 3/8	7	5/16	19	3/4	100	4	202	8
S-005	0.5					7	5/16	19	3/4
S-007	0.75					7	5/16	19	3/4
S-008	0.8					7	5/16	19	3/4
S-01	1.0					7	5/16	19	3/4
S-012	1.25					7	5/16	19	3/4
S-015	1.5					9	3/8	21	13/16
S-016	1.6					9	3/8	21	13/16
S-02	2.0					11	7/16	23	7/8
S-025	2.5					13	9/16	25	1
S-03	3.0	40	1 9/16	111	4 3/8	7	5/16	22	7/8	155	6 1/8	272	10 3/4
S-032	3.2					7	5/16	22	7/8
S-04	4					7	5/16	22	7/8
S-05	5					7	5/16	22	7/8
S-06	6					9	3/8	24	15/16
S-063	6.3					9	3/8	24	15/16
S-08	8					11	7/16	26	1
S-10	10					13	9/16	28	11/8

WHEN USING THE OVERLOAD DETECTOR, USE LIFTING ACCESSORIES WITH S.W.L. (SAFE WORKING LOAD) EQUAL TO, OR GREATER THAN THAT OF THE DETECTOR.
Eilon Engineering reserves the right to make changes without notice.

Print version